|
dumbass....
Did you go out and buy another one of these?
Last edited by jfowlzj95; 03-18-2008 at 06:25 PM.
will you stop postin that shite1!1
Most of my parts came in and I was able to get alittle done today. Had a problem with my order and somehow got a 96-98 crossmember so that pretty much put a halt on things. Should have that worked out tomarrow.
Still waiting on my Billstien 5100's
Then after the install Ill order my limit straps and whatnot
Got the stock skid out, crossmember, took sliderz off...
Used a flap disc to remove the paint on the unibody... THEN the power went out so I wasnt able to do the other side.. Had to to use the generator to try to finish this side and then I ran outta gas.. so that was the end of that.
Transmission mount is TOAST..
And here are some pics of my Switch board, and CB install that Ive been meaning to get up for a long time.
Switches are for front and rear lights, and then each wheel well individualy (rock lights)
And a SWR meter permanatly installed
Mic mount
Mic wire has quik disconnect so once disconnected you cant even tell I have a CB (as long as you dont notice the 4ft antenna..lol)
Speaker is for the CB
Showin some love
Heres some pics of my "rear bumper"...
I just cut the factory hitch off and rewelded it higher (zip ties are just holding on the trailer wireing loom)
Wo0t!!1
that remounting of the hitch looks slick man!
Mmm, finally a 'real' update.
I like the hitch/bumper idea too.
cool cb placement, i like the rock light controls too.
sick cb speaker too.
hmmm I like the hitch thing.... hmmm will have to do that to my front and rear hitches
thx for the comments guys...
Got some more done today..
Got the x-member screw up sorted out... Im goin to have to convert the tranny mount over to a 96-98 mount.. no biggy
Bolted in the xmember and dry fitted the other brackets
and yes I know the center of the xmember is in upside down...
just bolted it up in a hurry for mock up.. still have to pull the center back out to change the tranny mount
Check this out DJ here is your 14b and Dana 60 http://phoenix.craigslist.org/pts/631691352.html
Lol.. yeah thats the 14b Im picking up this weekend...
My66coupe on here is selling them...
Did you pick up the claytons flat belly skid. I would like to see more pics of that.
yup i got it... ill get pics...
ill get pics installed to.. should be in on sunday or monday
todays progress...
Bryant (Bshows) came over and helped weld in the claytons...
Drivers side rear mount ground for clearance
Kevins sliderz were modified to fit
Didnt get the belly pan in because DHL screwed up the shipping on the trans mount and it wont be here untill tomarrow...
But as soon as the mount goes in Ill get the belly pan in and get pics for you guys..
Ill install the front arms in the next few dayz, then onto the rear...
Thx Bryant for the help!!
Also picked up this beauty yesturday...
The start of my parts collecting for my next phase
Last edited by zj95; 04-13-2008 at 11:12 PM.
Looks good homo, who loaded that big axle up for you because I know your tiny ass didnt lift it.
lmao..
My66coupe, his buddy, and me all lifted it...
I dont even want to lift it off the trailer so Im just gonna leave it there untill I get my backhoe out then Ill lift it with that.. haha
So I need to make another trip up your way to help you out huh?
lol sure...
U can help me pull out the 8.8 and weld on the truss...
Nevermind.. you will prolly forget to put my lug nuts on...
U can lick my balls, I did put the lug nutz back on.
well your suppose to tighten them douche nozzle...
pfff whatever I made it home.
good thing you live in the middle of nowhere and dont need your jeep any time soon and can afford the down time.
your tire almost made it home before u....
« Previous Thread | Next Thread » |
Thread Information |
Users Browsing this ThreadThere are currently 1 users browsing this thread. (0 members and 1 guests) |