|
Yep. They asked if you wanted your vent done like mine. I said I bet you do, but you better ask!Originally Posted by Cue-Ball
These guys are really awesome! I asked Todd if they had anymore decals. There out, but when they get more, my rig will be sporting one of their badges.
I might add here, Donnie talked me out of turning up the pressures on mine (more) at this time. He said I was already running substantially higher pressures, and that it would steal pressure from the cooling circuits. He took it for a test drive before the service work and said, "Jerry, it's still pulling the front end up on the 1-2 shift. It really doesn't need anymore." So I relented. Cooling on mine will be more important, since I will be towing a camp trailer. And he agreed that once my stroker and lift (tires) are in, we could still bump it up a little more "if it really needs it".
Again, these guys are awesome.
Jerry
Last edited by I dig AU; 03-25-2006 at 10:46 AM.
Yea I will adjust that as I see fit when i take it down in a few weeks.
The stroker will be in by the time I take it back to get checked and tuned, so we may bump up the pressure at that time. We will just have to see.
Well, do ya like it?Originally Posted by Cue-Ball
Any ideas what was causing the leak on your original?
Yes I like it. They said it does not shift as firm as yours in the 1-2 shift, remember that I have the 249 so the full time four wheel drive is working against me there.
When I go back in a few weeks (after the stroker) then we will tweak it to shift firmer, if needed.
No word on the original leak, spent most of the day swapping in the new one, no time to deal with the old one.
nice to see somthing is getting done, what was the PITA factor on the tranny swap. and Ill try to make it on sat morn and see whats goin on.
Okay, here are some pix of the trans install and parts.
Some of the pix are a little blurry and it is hard to tell how much bigger the V8 parts are in the pix, but they are considerably bigger.
The V8 stuff is on the left and the stock stuff on the right, the pix are in no particular order.
The torque converter is an awesome piece it has a full billet cover and a larger clutch the factory one is a stamped steel piece with the mounting hole tabs welded on. This one uses a much bigger bearing and better clutches for better lock up.
Here are some more specs on it:
billet cover
hardened center pump hub and turbine spines
larger clutch for t/c lock up
clutch made of carbon fiber / kevlar
heavier springs for the clutch
fully rollerized bearings (no bushings)
Stay tuned for the stroker install on April 8th!!!!!!
Last edited by Cue-Ball; 03-28-2006 at 01:44 PM.
Just ordered my header, I went with the new Edelbrock one, was a little cheaper than the Banks but honestly when I saw them at Truckfest they looked almost the same, except the Edelbrock has a heat treatment where the Banks doesn't.
James over at Jeepers & Creepers hooked me up.
That looks good.
As to be expected with my Jeep the engine swap did not go completely as planned.
We got the stocker out but noticed an oil leak in the stroker so we dropped the pan and found a bad main bearing. Since no one carried the main bearings we have to order some up so we will hit it again next weekend.
Here are some pix of the progress.
Last edited by Cue-Ball; 04-10-2006 at 11:48 AM.
So the plan is for next sat? damn easter weekend, not sure if Ill be able to make it by for the swap. Im havin easter at my house this year so it mean the day before if the lets spend all day cleaning the fkn house.
how much was the header by the way?
thanks I just got my stuff from nick put on today and it sounds like a wet dream.Originally Posted by Cue-Ball
just the usualy high flow cat, series 70 flow. it purs like a fkn kitten I love it.
Im thinking about going up to lake pillsbury(sp) in medicino on either the 30 or 31, theirs some decent trails up their and a really good place to shoot. it has to be one of my fav. places to go camping. and theirs a pet semitart I am still trying to get pics of. its still in the planning stages but if you want to come I drive right by napa on the way up thier....
that is close to where i will be going to school next year maybe i will have to check it out sometime.
where you going sanoma(sp) my freinds gf goes their and we are prob going to try and teach her out to shhot the right way. she has never handled a gun before and shes 19. what kind of country is this??
Im going to chico not that close but close enough.
« Previous Thread | Next Thread » |
Thread Information |
Users Browsing this ThreadThere are currently 1 users browsing this thread. (0 members and 1 guests) |