|
|
11-19-2010, 11:36 PM
holy shit poor frame rail!
It's lookin good though man, looks like you have fun!
11-20-2010, 12:45 PM
Ha yea another submersion wheeler LOL. 10mpg brings the suck for sure though.
AP lovin the new sig.
11-20-2010, 02:57 PM
time to plate the frame and make some kinda slider or boat side
02-21-2011, 12:04 AM
I havent up dated this in while. I had planned on build a long arm set up and sliders over the winter. I live in a small apartment with my girlfriend and do all my work at my parents house. In November we lost the house to a fire but my mom dad brother and sister all made it out ok with the two dogs. The house and attached garage were total losses along with 4 cars 05 equinox 02 civic 88 cavalier z24 convertable and 85 S10 blazer with 450hp small block.
What was left of the house's contents took over the shop so my jeep sat in a snowbank for 4 months. With life getting back to normal i went to pull the jeep out and it was dead. no spark no fuel no gauges. After some research I swaped the pcm with the pcm out of my parts jeep and the old beast fired up! I sold the 35'' procomp and picked up a set of 5 34''trxus mt's on chrome soft 8s. I also picked a new DD 1998 Dakota 318 4x4. Ill try to get some pics up tommoro.
03-03-2011, 09:36 PM
Got the new Dodge on the road under $1500
The 34'' trxxus are all mounted up on the Jeep front bumper is off and that cross member is begging to be cut out.
Spare tire mounted rim is a little different but close enough
03-04-2011, 01:31 AM
Good build man. How was the rubbing w/35s on 3.5? Bumpstopped?
03-11-2011, 10:25 PM
The rubbing wasnt bad after all the trimming I did
Did some chopping on the front cross member and got the winch mount all tacked into place.
Much better approach angle compared to old.
OLD
NEW
03-12-2011, 10:10 AM
Nice work man. What are your plans for under the headlamps?
03-12-2011, 12:34 PM
Plan is to just bend up a simple tube bumper similar to the one posted in TOTM on bumpers/body protection
06-24-2011, 10:23 PM
jeep got tboned pics say it all
The body damage after destroying the altima front end
06-24-2011, 10:31 PM
Time to rebuild spare d30 with new WJ knuckles and rugged ridge steering.
3-link arms at ride height not as high as i wanted but better then what i had
drooping the front out
Waiting on shocks and brake lines. Coil is just starting to unseat rear tire is off the ground.
06-24-2011, 11:33 PM
nice, keep goin on it.
08-15-2011, 01:00 PM
unirail plated
sliders started
[IMG]
http://i691.photobucket.com/albums/v..._6982880_n.jpg[/IMG]
steering and tracbar angles
climbed the gravel pile
08-18-2011, 03:35 PM
so any updates on this? Maybe some off raodin pics or vids wheelin
10-12-2011, 07:04 PM
Back on the road again! Done some minor wheelin no pics but i gotta couple after shots including damage from the tree didnt see.
Gotta call to pull out a Tacoma easy recovery. Then I had to try the whole and sunk like a rock. Next morning shot
10-12-2011, 07:10 PM
New toy!
10-13-2011, 09:37 AM
What front arms did you go with? Maybe I missed it as I was browsing your thread, but I didn't see where you mentioned buying or building them.
10-13-2011, 12:17 PM
Just a homemade 3 link. Hard parts supplied By TMR Customs
10-13-2011, 12:37 PM
Any pics of the suspension you made? I'd like to see how you made the front and rear work and mounting locations....so on
10-13-2011, 12:52 PM
Rear is still on the short arms. Front is mounted off of the cross member. ill get some pics later
| « Previous Thread | Next Thread » |
| Thread Information |
Users Browsing this ThreadThere are currently 1 users browsing this thread. (0 members and 1 guests) |
