PDA

View Full Version : Parting Out 94 YJ 4.0 5 speed



KeepItCrunk
12-05-2005, 01:24 AM
2 AX-15's, 1 good, 1 bad, bad has centerforce series 1 clutch. 750/bo
5 BFG mud terrains. 33 12.50 15. 1 never touched pavement, others have around 2k on them, no cuts, slashed, chips or chunks. 650/bo
4.0. Not sure of mileage. actualy jeep had 178k on it... But i know for a fact it was in an accident and the engine was replaced. Runs smooth and quiet as if it were new. ill tell you why if your interested in it. 600/bo
Wheel bearings, around 3k on them. 150/bo
Rotors, Calipers, pads, less than 5k. 200/bo
Font Buckets and rear bench from sahara, sahara green with tan piping. Comes with brackets. 175/bo
Tj rear bench, grey everything. 60/bo
posi-lock, used, back in box, full instructions, gaskets, bolts etc. 150/bo
Rear Driveshaft, long yolk style, lets you go to 3.5-4.5 inches w/o a SYE. 40/bo.
YJ 231, new slip yolk seal. works fine. 150/bo
XJ 231, Sitting here, kid told me it had a streched chain... seems fine, project t-case ;-) 60/bo.
Rear YJ 3.5 fabtech leafs. 50/bo
Custom rear bumper. d ring mounts. receiver, reverse light mounts, quite beefy :D 250/bo
Custom Front bumper, integrated fog lights, grate top, winch plates, stinger mount, d ring mounts. VERY STRONG!!! (i told my friends it was stronger then my frame... well, i rolled it, and its still as level as the day i put it on, yet the frame behind it completely buckled and was torn apart...) looks sweeeet. subtle yet destructive ;-) 300/bo
YJ Hardtop, fully insulated, has defrost, light and a wiper. 650/bo
Fiberglass YJ hood. Minor damage, scrapes in one spot from minor contact from rollover. 75/bo
I have tons of interior stuff and engine stuff. if you need anything let me know cause i got a complete yj in my garage that was working 100% before it rolled. front axle, frame body and front fenders along with the rollbar are destroyed. aside from that, everythings great!! :D lemme knowwwww. i needa get rid of all of this stuff cause i wanna start building the ZJ!!!!

jeep4x4nut
12-05-2005, 10:38 AM
interested in selling whole jeep?

KeepItCrunk
12-05-2005, 08:06 PM
i would... but i got bored and took everything apart and i didn;t have an engine hoist... so i just started chopped the frame and body away hopefully until it's just the engine... so i got lost of pieces

Hurricane 4x4
12-06-2005, 02:35 PM
what axle does the posi lock you mention fit?

Silver85327
12-06-2005, 04:25 PM
I am interested in the xfer cases. Does either one of them have a 23 spline input?

Silver85327
12-06-2005, 04:28 PM
I would be most interested in the XJ case. Have money waiting on your response.

KeepItCrunk
12-07-2005, 12:28 AM
Well, it will fit any central disconnect dana 30, like those in a YJ or some XJ's, older ones. Its manually moves the collar to lock the inner shaft to the outer shaft, making the spiders turn with the carrier, inster of the carrier jsut spinning around them. Its not al actual locker, they just make it sound that way so ppl get psyched.

Silver85327
12-07-2005, 08:05 PM
still interested in the YJ xfer case send me a email Silver85327@hotmail.com With your paypal information. So I can get that money + shipping costs sent to you. My shipping zip is 78336 if you want to find out exactly how much it is going to cost to get it here so i can send you a lump sum.

Silver85327
12-08-2005, 05:53 PM
Hello? Are you still selling it or what?