Swamp boy
10-30-2005, 10:40 PM
Donzi is selling his since he moved to Sweden and its just to expensive to ship...
Here is his post ...........
1979 Jeep Cherokee
The truck needs a little TLC,But runs good...
Some of the goodies....
Multimount warn XD9000I(Has the usual problem..Needs some wiring work..)
MSD all in one distributor ignition system ..Brand new maybe 10 miles..
AMC 360 professionally reconditioned heads , ported ,valve job new springs etc.
Custom Ground Engle cam.
Edelbrock intake
Holley Truck avenger carb
TH 400
BW 1339 w/ low range and machanical shiftor or air shifter (manual installed air shifter included needs to be installed..)
York Compressor converted to OBA but not wired up (works perfectly but did not finish rewireing before moved to sweden...)
2 air tanks ..(Made out of scuba tanks.)
Rear mounted Matteries with cab isolator switch
High angle drive shaft for front.
Roll cage (S&W Racecar 10 point )
Comfy bucket seats
Hummer beadlocks
35" SX's 30, 40 % tread
2 confer tool boxes
High amp alternator
Light bar with 6 lights
electric fan
22gallon fuel cell
Dana 44 front 3:55 welded..
Rancho 44044 front springs 2.5" lift for SJ 6" lift for chevy
Long travel shocks
14 bolt FF with 3:73 welded spiders but can be replaced with open..
63" chevy rear springs
Hydro-assist system , steering box, ram , etc..
Hurculined fenders and roof and pimp ass racing stripe..
All tools and spare parts that are in the truck are included , including tow strap shackles , snatch blocks,poly motor mounts , Z drive shifter , motor mounts, drive flanges , and U joints ..
also have a set of M 715 half doors and a new hood that are ready to be installed if you want...
Asking $3500 ...OBO...
Now..I welded the cage in and did alot of the other work so if you are interested and have any questions just ask...
It is a very nice ride.. Here are a few pics..http://i12.photobucket.com/albums/a207/Donzi4x4/NewOrleanssummer05014.jpg
http://i12.photobucket.com/albums/a207/Donzi4x4/NewOrleanssummer05022.jpg
http://images.igloos.ca/d/108331-1/NewOrleanssummer05024.jpg
in one of the threads about roll cages I posted some pics of it.. It is a full 10 point cage but it could use some triangulation on the rear down tubes ...
This used to be an SJ.. I cut the back off and moved the window rail forward .. So it still has a rear window...(Made of Plexi..and cut around the roll cage..)
Last time Jeff was in from Sweden we pulled out all the wireing under the hood and started cleaning it up.. We got it running but didnt reconnect the OBA ..There are a few other imperfections but it has been a trail rig.. It is licensed and registered ...It passes inspections here .(No emissions..)
Here is his post ...........
1979 Jeep Cherokee
The truck needs a little TLC,But runs good...
Some of the goodies....
Multimount warn XD9000I(Has the usual problem..Needs some wiring work..)
MSD all in one distributor ignition system ..Brand new maybe 10 miles..
AMC 360 professionally reconditioned heads , ported ,valve job new springs etc.
Custom Ground Engle cam.
Edelbrock intake
Holley Truck avenger carb
TH 400
BW 1339 w/ low range and machanical shiftor or air shifter (manual installed air shifter included needs to be installed..)
York Compressor converted to OBA but not wired up (works perfectly but did not finish rewireing before moved to sweden...)
2 air tanks ..(Made out of scuba tanks.)
Rear mounted Matteries with cab isolator switch
High angle drive shaft for front.
Roll cage (S&W Racecar 10 point )
Comfy bucket seats
Hummer beadlocks
35" SX's 30, 40 % tread
2 confer tool boxes
High amp alternator
Light bar with 6 lights
electric fan
22gallon fuel cell
Dana 44 front 3:55 welded..
Rancho 44044 front springs 2.5" lift for SJ 6" lift for chevy
Long travel shocks
14 bolt FF with 3:73 welded spiders but can be replaced with open..
63" chevy rear springs
Hydro-assist system , steering box, ram , etc..
Hurculined fenders and roof and pimp ass racing stripe..
All tools and spare parts that are in the truck are included , including tow strap shackles , snatch blocks,poly motor mounts , Z drive shifter , motor mounts, drive flanges , and U joints ..
also have a set of M 715 half doors and a new hood that are ready to be installed if you want...
Asking $3500 ...OBO...
Now..I welded the cage in and did alot of the other work so if you are interested and have any questions just ask...
It is a very nice ride.. Here are a few pics..http://i12.photobucket.com/albums/a207/Donzi4x4/NewOrleanssummer05014.jpg
http://i12.photobucket.com/albums/a207/Donzi4x4/NewOrleanssummer05022.jpg
http://images.igloos.ca/d/108331-1/NewOrleanssummer05024.jpg
in one of the threads about roll cages I posted some pics of it.. It is a full 10 point cage but it could use some triangulation on the rear down tubes ...
This used to be an SJ.. I cut the back off and moved the window rail forward .. So it still has a rear window...(Made of Plexi..and cut around the roll cage..)
Last time Jeff was in from Sweden we pulled out all the wireing under the hood and started cleaning it up.. We got it running but didnt reconnect the OBA ..There are a few other imperfections but it has been a trail rig.. It is licensed and registered ...It passes inspections here .(No emissions..)