PDA

View Full Version : Jeep Stuff



nate
04-23-2005, 09:05 PM
Argon/Co2 flow meter for MIG welder. Dial style, not the ball type. I paid $75 for this about a year ago, barely used. $40

Electric Fan controller. Comes with home brew wire harness and a 30 amp relay. Works fine, just went with a different setup. $10

WJ 4.0 electric fan mounted in a stock ZJ shround. Cleanly done, fit great in my Jeep. Upgraded to a Taurus fan. $40 Will include fan controller for $45.

8.8" Crush Collar eliminator $5

9" ring gear bolts (new of course) $5

shortys ZJ
04-26-2005, 08:33 PM
Do you have any pics of the RE springs? What condition are the T-case drop brackets? Thannks for the Tie rod flip inserts!

phillyzj
04-26-2005, 08:51 PM
also interested in the coils, how long you run them? sagged at all? How much for shipping 19104? www.iship.com i can do paypal/whateves.

nate
04-27-2005, 05:01 AM
Drop brackets are good shape, I mean they are just spacers, not really anything you could wear out or anything.

Coils are 2 years old. With all the shit in my Jeep, they are close to 4.5"

phillyzj
04-28-2005, 12:37 PM
i'm still interested, how much to ship?

Forwheelin49
04-28-2005, 07:59 PM
well if the deal for the re ca drop brackets falls through hit me up

gsh
04-29-2005, 09:21 PM
I'm interested in the following:

>2 knuckles off 85 XJ D30 $10

Assuming L&R. How's the shoe guides?

>Rubicon Express Hack and Tap. Complete kit, I can even throw in a cut mainshaft if you want it $50

RE lists pre- & post- '96, which?
The shaft is for; 242, 231 long tail, 231 short tail, or?

>2 Rubicon Express sway bar discos. They are worn and beat up. Still work $20

Length?

>Ford 8.8 4.56 gears, 5000 miles on them, Genuine Gear, run a bit loud $20

>LP D30 4.56 gears, about 10,000 miles, good shape. $40

nate
05-02-2005, 08:13 AM
Yup 2 knuckles, left and right. shoe guides are good. These knuckles are for the older D30s, different than the newer stuff (like ZJs). They will fit, but the brakes and bearings are different.

Hack and Tap is post 96. Mainshaft is from a 99 NP231. The hole is a bit off center, though I don't remember drilling it off center... worked ok though.

Discos... for 4.5" lift. I think 6" pins. For the shape they are in, I'd take like $10. They work, but they have been used.

Gears are gone, traded them for a spare tire.

gsh
05-02-2005, 11:53 PM
Ah, none fits my plans then. Thanks anyway.

ATL ZJ
05-03-2005, 12:28 AM
What drive is the Impact? 1/2"? Torque rating? How much shipped to 30327?

nate
05-04-2005, 08:07 AM
Yeah it's 1/2" I would say probably 150 ft/lbs, maybe 200. Made by All Trade. Probably will cost more to ship than it's worth, but I can find out if you really want.

nate
05-10-2005, 07:24 AM
List updated. I'm quite surprise no one would be interested in some of this stuff. wheel bearings, steering parts?? Shipping isn't that bad if I go with USPS. Guesstimate what the weight it, or email me and I'll weigh it.. shipping from 99504.

nate
05-13-2005, 06:59 AM
TTT, list updated with new stuff and lower prices. Most of it will be going to the dump next week.

Grandsrus
05-25-2005, 02:34 PM
Sent email on brackets...

Cue-Ball
05-25-2005, 03:39 PM
email sent.

nate
05-26-2005, 01:56 AM
I just updated the list. I'm looking to clean out the garage, so best offer applies. Shipping is 99504. If I go with USPS, it's not too bad, so don't let the fact I like in AK discourage you.

Cue-Ball
05-26-2005, 11:41 AM
Nate,

You say you have a "washable" tranny filter now, what is it you are using??

If the HUBs will fit in the 91 XJ axle I have I am interested, let's work something out.

wwbmopar
06-28-2005, 08:36 AM
Whats the shipping on the fan controller to Wyoming 82001

UNIMOG69
07-03-2005, 11:17 AM
Discos... for 4.5" lift. I think 6" pins. For the shape they are in, I'd take like $10. They work, but they have been used.

I WANT THESE... Do you still have them? I emailed you a bit ago about these.

jeep4x4nut
07-05-2005, 01:52 AM
PM sent!!!!!

nate
07-05-2005, 05:35 AM
Guys, this stuff was listed back in May. I threw most of it out when I moved Memorial Day weekend.

I did update this list for yall.