OverkillZJ
12-26-2006, 06:14 PM
OK, time to clean out the garage, and that means sell stuff.
ALL PRICES ARE LOCAL PICKUP, CONTACT ME IF YOU WANT TO DISCUSS SHIPPING. I’m located in South Fayette barely south of Bridgeville PA: 15017. PM for details.
First up: a Corbeau reclining seat. It was a display unit at 4WDH, never installed since then. No hardware included but the seat itself. Like new, $175
http://www.fccsonline.com/forsale/seat1.jpg
Next up: Corbeau Baja suspension seats. Never installed, was planning on using in buggy but prefer a 2-seater. Asking $300 for the pair and would prefer not to separate.
http://www.fccsonline.com/forsale/suspseat.jpg
Also selling a new (reman) steering box. I bought this trading in my old box last year before the rig was buggied, should be like new and no core fee needed. Out of a 1997 ZJ, should work in just about any rig that used these boxes (TJ/XJ/ZJ/YJ etc). $175 for local pickup.
http://www.fccsonline.com/forsale/steeringbox.jpg
Also selling two 35 spline shafts from a Ford F350 HP60 front. Was replaced with aftermarket shafts: these are 35 spline inner, 30 spline outers. Probably need new ujoints. $75 per side local pickup
http://www.fccsonline.com/forsale/60shafts.jpg
Never used spare pitman rod-end from the Currie HD steering setup. This was never used and bought as a spare, $40 local pick up
http://www.fccsonline.com/forsale/pend.jpg
http://www.fccsonline.com/forsale/pend2.jpg
Ujoint style Dana30 (HP or LP) ubolt style yoke with ubolts: $25 local pickup
http://www.fccsonline.com/forsale/30yoke.jpg
Relatively new D30 front calipers from 97ZJ: There are remans that were only on the road for one year, probably about 8,000 miles on them. Asking $35 / side with the pads.
http://www.fccsonline.com/forsale/frontcalipers.jpg
Stock 60 cover from 1978 F35 HP60 front axle; $10
http://www.fccsonline.com/forsale/60cover.jpg
High Pinion 30 housing with knuckles: no shafts / hubs, just the housing w/ knuckles: $40 local pickup
http://fccsonline.com/forsale/HP30.jpg
ALL PRICES ARE LOCAL PICKUP, CONTACT ME IF YOU WANT TO DISCUSS SHIPPING. I’m located in South Fayette barely south of Bridgeville PA: 15017. PM for details.
First up: a Corbeau reclining seat. It was a display unit at 4WDH, never installed since then. No hardware included but the seat itself. Like new, $175
http://www.fccsonline.com/forsale/seat1.jpg
Next up: Corbeau Baja suspension seats. Never installed, was planning on using in buggy but prefer a 2-seater. Asking $300 for the pair and would prefer not to separate.
http://www.fccsonline.com/forsale/suspseat.jpg
Also selling a new (reman) steering box. I bought this trading in my old box last year before the rig was buggied, should be like new and no core fee needed. Out of a 1997 ZJ, should work in just about any rig that used these boxes (TJ/XJ/ZJ/YJ etc). $175 for local pickup.
http://www.fccsonline.com/forsale/steeringbox.jpg
Also selling two 35 spline shafts from a Ford F350 HP60 front. Was replaced with aftermarket shafts: these are 35 spline inner, 30 spline outers. Probably need new ujoints. $75 per side local pickup
http://www.fccsonline.com/forsale/60shafts.jpg
Never used spare pitman rod-end from the Currie HD steering setup. This was never used and bought as a spare, $40 local pick up
http://www.fccsonline.com/forsale/pend.jpg
http://www.fccsonline.com/forsale/pend2.jpg
Ujoint style Dana30 (HP or LP) ubolt style yoke with ubolts: $25 local pickup
http://www.fccsonline.com/forsale/30yoke.jpg
Relatively new D30 front calipers from 97ZJ: There are remans that were only on the road for one year, probably about 8,000 miles on them. Asking $35 / side with the pads.
http://www.fccsonline.com/forsale/frontcalipers.jpg
Stock 60 cover from 1978 F35 HP60 front axle; $10
http://www.fccsonline.com/forsale/60cover.jpg
High Pinion 30 housing with knuckles: no shafts / hubs, just the housing w/ knuckles: $40 local pickup
http://fccsonline.com/forsale/HP30.jpg